Phụ Tùng Thay Thế

Hiển thị 1–25 của 88 kết quả

  • AMAC HSC (Hydraulic Swing Clamp Product type)

    Quick View
  • AMAC HTM/HTB (Hydraulic Thin-type Cylinder Product type)

    Quick View
  • Bơm chân không Orion KRF25A (Dry pump)

    Quick View
  • Bơm dầu bôi trơn SKF FLMF (Electrically operated vane pumps for use in oil circulation systems)

    FLMF allows the pump to be flange-mounted on the reservoir (FLMF) both vertically and horizontally. When installed on the side (horizontally), the unit should be mounted above the maximum lubricant level.
    High suction capacity (3 m)
    Designed for 24/7 operation
    Delivers oil and air mixtures
    Fail safe running functions

    Quick View
  • Bơm dầu SKF MKU (MKU gear pump unit)

    Function principle Electrically operated gear pump
    Lubricant
    MKU; MKL mineral oil or synthetic oil, 20-1500 mm²/s
    MKF fluid grease NLGI 000 or 00
    Number of lubricant outlets 1
    Metering quantity 100; 200; 500 cm³/min 6; 12; 31 in³/min
    Operating temperature +10 to 40 °C +50 to 104 °F
    Operating pressure max. 30 bar 435 psi
    Capacity of the reservoir 2,0; 3,0 and 6,0 l 0.5, 0.8 and 1.6 gal
    Material (reservoir) plastic, metal
    Connection outlet G 1/4
    Protection class IP 54
    Voltage 24 V DC
    115 or 230 V AC; 50/60 Hz
    Dimensions depending on reservoir
    2 l; 0.5 gal plastic 204 × 130 × 298 mm 8 × 5.2 × 11.7 in
    3 l; 0.8 gal plastic 286 × 132 × 298 mm 11.3 × 5.2 × 11.7 in
    3 l; 0.8 gal metal 286 × 132 × 313 mm 11.3 × 5.2 × 12.3 in
    6 l; 1,5 gal plastic 290 × 178 × 334 mm 11.4 × 7 × 13.2 in
    Mounting position vertical

    Quick View
  • Bơm màng Yamada NDP-15BAT (Diaphragm Pump)

    Nominal port size 1/2″(15A)
    Connection to liquid Inlet Rc1/2
    Outlet
    Air connection Inlet Rc1/4 (with an air cock)
    Exhaust Rc3/8 (Equipped with a muffler)※
    Air supply pressure range 0.2~0.7MPa
    Maximum discharge pressure 0.7MPa
    Discharge volume/cycle 70mL
    Limit of slurry 1mm以下
    Weight NDP-15BA□:4.1kg
    NDP-15BS□:6.3kg
    NDP-15FP□:3.5kg
    NDP-15FVT :4.3kg

    Quick View
  • Bơm màng Yamada NDP-25BSN (Diaphragm Pump)

    Nominal port size 1″(25A)
    Connection to liquid Inlet Flange JIS 10K 25A or equivalent ※
    Outlet
    Air connection Inlet Rc3/8 (with an air cock)
    Exhaust Rc3/4 (Equipped with a muffler) 0
    Air supply pressure range 0.2~0.7MPa
    Maximum discharge pressure 0.7MPa
    Discharge volume/cycle Rubber diaphragm type: 600mL
    Fluorocarbon resin diaphragm type: 500mL
    Limit of slurry 3mm or less
    Weight :
    NDP-25BA□:13.0kg
    NDP-25BS□:20.0kg
    NDP-25BF□:20.0kg
    NDP-25BP□:11.0kg
    NDP-25BV□:13.5kg

    Quick View
  • Bơm màng Yamada NDP-P20 (Diaphragm Pump)

    Quick View
  • Bơm mỡ ESCO EA166SG-3B (400ml grease gun (key type))

    Nozzle length 170mm Flexible hose length 230mm
    Tube size φ60 × 300mm capacity 400ml
    Working pressure 0.59MPa Inlet Rc (PT) 1/4 ”
    Nozzle screw size R1 / 8 \ ” Applicable grease Bellows grease

    Quick View
  • Bơm mỡ ESCO EA991CM (Grease Pump)

    NLGI-0 to 1
    Capacity-500ml
    Maximum discharge pressure-49MPa
    Pipe length-375mm
    Nozzle length-170mm
    The greases EA991C-1 to -3 and -11 to -13 can be used without any change.
    Applicable grease Bellows grease、Hand grease

    Quick View
  • Bơm mỡ Yamada SKR-55EX (Grease Lubricator)

    Quick View
  • Bơm tay ESCO EA990K-5A ([Manual] Kerosene Pump)

    Application-Kerosene, light oil, and solvent
    Discharge rate-6.7L/min
    Suction pipe tip diameter φ15mm

    Quick View
  • Cảm biến Panasonic EX-21B (Ultra-compact Photoelectric Sensor)

    Product Number : EX-21B
    Part Number : EX-21B
    CE marking directive compliance EMC Directive, RoHS Directive
    Sensing range : 1 m 3.281 ft
    Sensing object : Min. dia. 2.6 mm dia. 0.102 in opaque object (Setting distance between emitter and receiver: 1 m 3.281 ft)
    Hysteresis –
    Repeatability(perpendicular to sensing axis) : 0.05 mm 0.002 in or less
    Supply voltage 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
    Current consumption : Emitter: 10 mA or less
    Receiver: 10 mA or less
    Output NPN open-collector transistor
    – Maximum sink current: 50 mA
    – Applied voltage: 30 V DC or less (between output and 0 V)
    – Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
    Output:Utilization category : DC-12 or DC-13
    Output:Short-circuit protection : Incorporated
    Response time : 0.5 ms or less
    Operation indicator : Orange LED (lights up when the output is ON) (located on the receiver)
    Stability indicator : Green LED (lights up under stable light received condition or stable dark condition), located on the receiver
    Sensitivity adjuster –
    Operation mode switch –
    Protection : IP67 (IEC)
    Ambient temperature : -25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
    Ambient humidity : 35 to 85 % RH, Storage: 35 to 85 % RH
    Ambient illuminance : Incandescent light: 3,000 lx or less at the light-receiving face
    Voltage withstandability : 1,000 V AC for one min. between all supply terminals connected together and enclosure
    Insulation resistance : 20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
    Vibration resistance : 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each
    Shock resistance : 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
    Emitting element : Red LED (modulated)
    Emitting element:Peak emission wavelength : 640 nm 0.025 mil
    Material : Enclosure: Polyethylene terephthalate
    Lens: Polyalylate
    Cable : 0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
    Cable extension : Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable (both emitter and receiver).
    Weight : Net weight (each emitter and receiver): 20 g approx
    Gross weight: 60 g approx
    Accessory –

    Quick View
  • Cảm biến Panasonic EX-31B (Threaded Miniature Photoelectric Sensor)

    Product Number : EX-31B
    Part Number : EX-31B
    CE marking directive compliance EMC Directive, RoHS Directive
    Sensing range : 500 mm 19.685 in
    Sensing object : dia. 2 mm dia. 0.079 in or more opaque object (Completely beam interrupted objects)
    Hysteresis –
    Repeatability(perpendicular to sensing axis) : 0.05 mm 0.002 in or less
    Supply voltage 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
    Current consumption: Emitter: 10 mA or less
    Receiver: 10 mA or less
    Output NPN open-collector transistor
    – Maximum sink current: 50 mA
    – Applied voltage: 30 V DC or less (between output and 0 V)
    – Residual voltage: 2 V or less (at 50 mA sink current), 1 V or less (at 16 mA sink current)
    Output:Utilization category : DC-12 or DC-13
    Output:Output operation Dark-ON
    Output:Short-circuit protection Incorporated
    Response time : 0.5 ms or less
    Operation indicator : Orange LED (lights up when the output is ON)
    (incorporated on the receiver)
    Stability indicator : Green LED (lights up under stable light received condition orstable dark condition, incorporated on the receiver)
    Sensitivity adjuster –
    Pollution degree : 3 (Industrial environment)
    Protection : IP67 (IEC)
    Ambient temperature : -25 to +55 degrees -13 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -30 to +70 degrees -22 to +158 degrees Fahrenheit
    Ambient humidity : 35 to 85 % RH, Storage: 35 to 85 % RH
    Ambient illuminance : Incandescent light: 3,000 lx or less at the light-receiving face
    Voltage withstandability : 1,000 V AC for one min. between all supply terminals connected together and enclosure
    Insulation resistance : 20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
    Vibration resistance : 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude (20 G max.) in X, Y and Z directions for two hours each
    Shock resistance : 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
    Emitting element : Red LED (modulated)
    Material : Enclosure: Die-cast zinc (Nickel plated)
    Lens: Polycarbonate
    Enclosure cover: Polycarbonate
    Cable : 0.1 mm2 3-core (emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
    Cable extension Extension up to total 50 m 164.042 ft is possible with 0.3 mm2, or more, cable (both emitter and receiver).
    Weight : Net weight (each emitter and receiver): 20 g approx
    Gross weight: 50 g approx
    Accessory : Nut: 2 pcs
    Toothed lock washer: 2 pcs

    Quick View
  • Cảm biến Panasonic HG-C1200 (CMOS type Micro Laser Distance Sensor)

    Product Number HG-C1200
    Part Number HG-C1200
    Applicable standard EMC Directive Compliance, FDA Standard
    Measurement center distance 200 mm 7.874 in
    Measuring range ±80 mm 3.150 in
    Repeatability 200 μm 7.874 mil
    Linearity ±0.2%F.S.
    Temprerature characteristics 0.03% F.S./℃
    Light source Red semiconductor laser Class 2 [JIS/IEC/GB/FDA (Note) ]
    Max. output: 1 mW
    emission peak wavelength: 655 nm 0.026 mil
    (Note) This product complies with 21 CFR 1040.10 and 1040.11 Laser Notice No. 50, dated June 24, 2007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration).
    Beam diameter ø300 μm 11.8111 mil approx.
    (Note) This is the size in the measurement center distance. These values were defined by using 1/e2 (13.5% approx.) of the center light intensity. Due to leak light outside the specified area, the reflectance around the detecting point may be higher than at the point and this may affect the measurement value.
    Supply voltage 12 to 24 V DC ±10 %, Ripple P-P 10 % or less
    Current consumption 40 mA or less (at 24V DC supply voltage)
    65 mA or less (at 12V DC supply voltage)
    Note : Specifications have been changed from shipment in August, 2016. For shipment before July 2016 : 40 mA or less (at 24 V DC supply voltage), 60 mA or less (at 12 V DC supply voltage)
    Control output NPN open-collector transistor
    – Maximum sink current: 50 mA
    – Applied voltage: 30 V DC or less (Between control output to 0V)
    – Residual voltage: 1.5 V or less (At 50 mA sink current)
    – Leakage current: 0.1 mA or less
    Control output:Output operation Either Light-ON or Dark-ON
    Control output:Short-circuit protection Incorporated (Auto reset type)
    Analogue output : Analog voltage output • Output range: 0 to 5 V (at alarm: +5.2 V)
    • Output impedance: 100Ω
    Analogue output : Analog current output • Output range: 4 to 20mA (at alarm: 0mA)
    • Output impedance: 300Ω or less
    Note : Analog current output has been added from shipment in August 2016.
    Response time Switchable between 1.5 ms / 5 ms / 10 ms
    External input NPN non-contact input
    – Input conditions
    Invalid: +8 to +V DC or Open
    Valid: 0 to +1.2 V DC
    – Input impedance: 10 kΩ approx.
    Pollution degree 2
    Operating altitude 2,000 m 6561.680 ft or less
    Protection IP67 (IEC)
    Ambient temperature -10 to +45 ℃ -14 to 113 ℉ (No dew condensation or icing allowed), Storage: -20 to +60 ℃ -4 to 140 ℉
    Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
    Ambient illuminance Incandescent light: 3,000 ℓx or less at the light-receiving face
    Vibration resistance 10 to 55 Hz (period: 1 min.) frequency, 1.5 mm 0.059 in double amplitude in X, Y and Z directions for two hours each
    Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
    Cable 5-core composite cable, 2 m 6.5617 ft long
    Cable extension Extension up to total 10 m 393.701 ft is possible with 0.3 mm2, or more, cable.
    Material Enclosure: Aluminum die-cast
    Front cover: Acrylic
    Weight Net weight: 35 g approx. (without cable), 85 g approx. (including cable)

    Quick View
  • Cảm biến Panasonic NA2-N28 (General Purpose & Slim Body Area Sensor)

    Product Number NA2-N28
    Part Number NA2-N28
    CE marking directive compliance EMC Directive, RoHS Directive
    Sensing height 540 mm 21.260 in
    Sensing range 5 m 16.404 ft
    Beam pitch 20 mm 0.787 in
    Sensing object dia. 30 mm dia. 1.181 in or more opaque object (completely beam interrupted objects)
    Supply voltage 12 to 24 V DC plus or minus 10 % Ripple P-P 10 % or less
    Power consumption:Emitter:Job indicator ON 1.2 W or less
    Power consumption:Emitter:Job indicator OFF 1.1 W or less
    Power consumption:Receiver:Job indicator ON 1.2 W or less
    Power consumption:Receiver:Job indicator OFF 1.1 W or less
    Output NPN open-collector transistor
    – Maximum sink current: 100 mA
    – Applied voltage: 30 V DC or less (between output and 0 V)
    – Residual voltage: 2 V or less (at 100 mA sink current), 1 V or less (at 16 mA sink current)
    Output:Utilization category DC-12 or DC-13
    Output:Output operation ON when all beam channels are received (OFF when one or more beam channels are interrupted)
    Output:Short-circuit protection Incorporated
    Response time 10 ms or less (12 ms or less when the interference prevention function is used)
    Indicators:Emitter Emitting indicator: Green LED x 2 (light up during emission; one LED lights up for Frequency A setting, both LEDs light up for Frequency B setting)
    Job indicator: Red LED (lights up, blinks or lights off when the job indicator input is applied, selected by operation mode switch)
    Indicators:Receiver Operation indicator: Red LED (lights up when one or more beam channels are interrupted)
    Stable incident beam indicator: Green LED (lights up when all beam channels are stably received)
    Job indicator: Red LED (lights up, blinks or lights off when the job indicator input is applied, selected by operation mode switch)
    * When an excess current flows through the output, the stable incident beam indicator and the operation indicator on the receiver blink simultaneously due to operation of the short-circuit protection circuit.
    Interference prevention function : Incorporated
    Test input (emission halt) function : Incorporated
    Pollution degree 3 (Industrial environment)
    Protection IP40(IEC)
    Ambient temperature -10 to +55 degrees +14 to +131 degrees Fahrenheit (No dew condensation or icing allowed), Storage: -10 to +60 degrees +14 to +140 degrees Fahrenheit
    Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
    Ambient illuminance Incandescent light: 3,000 lx or less at the light-receiving face
    Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
    Insulation resistance 20 MOhm , or more, with 250 V DC megger between all supply terminals connected together and enclosure
    Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each
    Shock resistance : 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
    Emitting element : Infrared LED (Peak emission wavelength: 870 nm 0.034 mil, modulated) (Note:Peak emission wavelength has been changed from production in March, 2017.)
    Material : Enclosure: Heat-resistant ABS
    Lens cover: Polyester
    Indicator cover: Acrylic
    Cable : 0.2 mm2 4-core cabtyre cable, 3 m 9.843 ft long
    Cable extension : Extension up to total 25 m 82.021 ft is possible for both emitter and receiver, with 0.2 mm2, or more, cable.
    Weight(Total weight of emitter and receiver) : Net weight: 650 g approx.
    Gross weight: 800 g approx.

    Quick View
  • Cảm biến Panasonic WTKG2411-P

    Dòng điện định mức : 3A
    Đường kính : 070
    Thời gian hẹn giờ tắt : 10 giây – 30 phút
    Tuổi thọ pin : 100.000 bật tắt

    Quick View
  • Cảm biến quang Panasonic CX-491 (Photoelectric Sensor)

    Cable Length: 2mHousing
    Material: PBTInput
    Voltage: 12-24VDCMax
    Operating Temperature: 131 F
    Min Operating Temperature: -13 F
    Output Mode: PNP
    Protection Rating: IP67
    Response Time: 1 ms or less
    Scanning Distance: 3 m

    Quick View
  • Cáp 1T ESCO EA981DA-2 ([Heat-resistant] Multi

    Core strings-Kevlar
    Covering cloth-Polyester
    Heat-proof temperature-200℃
    Lift capacity 1.0t
    Width 52mm
    Length 2.0m

    Quick View
  • Cáp cẩu ESCO EA981DR-2.5 ([Waterproof] Multi Sling)

    No Water Or Oil Will Be Absorbed (reassuring To Work When Raining)
    The width : 40mm
    Lift Capacity : 1.0t
    Full length : 2.5m
    Material : Core thread:Polyester,
    Side fabric:Nylon (elastomer processed)

    Quick View
Contact Me on Zalo
X